Specifications of Plasma cutting machine

Horizontal guide rail: 2200/2600mm (standard configuration)
Total lifting stroke: 105mm
Air travel speed: 0-8000mm/min
Oxygen pressure: 0.5-1.2Mpa
Flame cutting speed: 50-900mm/min
Lateral effective travel: 1600/200mm
Cutting speed: 0-6000mm/min
Repetitive positioning accuracy: ± 0.2mm
Gas pressure: 0.04-0.1Mpa
Plasma cutting speed: 100-6000mm/min
Vertical guide rail: 3000/3500mm (standard configuration) can be customized according to users
Longitudinal effective travel: 2500/3000mm (total length minus 500mm)

Plasma cutting machine最先出现在Professional machinery supplier。

The high speed steel-drum production line is mainly comprised of 5 lines:

1. Uncoiling and flattening Stagger Blanking line II：

2. Blanking of Drum Top & Bottom Equipment of steel drum production line

3. Seam Welding lines

4. Middle-Section- Production Equipment

5. Rear treatment line

High Speed Steel-Drum Production Line最先出现在Professional machinery supplier。

Characteristics of Electrical punching press

Use a roller clutch for accurate positioning. Single and continuous flushing are available for safe operation. The design is exquisite and does not take up space. Smooth operation and low noise. Easy to adjust and maintain.

Local parameters; The unified upper mold hole size is 25.4, and an optional photoelectric protection device can be installed.

Manual press operation

Footer operation optional

Specifications of Electrical punching press

Electrical punching press compression machine最先出现在Professional machinery supplier。

Kneaders are widely used in high viscosity sealant, silicone rubber, CMC, adhesive, and also in battery, ink, pigment, dye, resin, plastic, rubber, cosmetics and other industries.

The Kneader is made of vacuum, pressure and atmospheric pressure. The heating and cooling structure includes jacket and outer half pipe. The heating and cooling methods include steam, heat transfer oil, hot water and water cooling. Hydraulic cylinder turning and cap opening are adopted.

The discharging modes of the Kneader reactor include hydraulic cylinder tilting, ball valve discharging, screw extrusion, etc. It can also install various safety, measurement, control record and other instruments on the Kneader reactor. The mixing cylinder body and the material contact part are made of stainless steel to ensure the purity of the products. The shaft seal of the Kneader reactor adopts a vacuum box balance structure to ensure the shaft seal, effectively prevent the black particles from entering the cylinder body due to the wear of the filler, and ensure the quality of the materials.

Models selection of kneaders

Plastic Rubber mixing machine Kneaders 5L-3000L最先出现在Professional machinery supplier。

Busbar punching/bending/cutting machine

3-in-1 Hydraulic Busbar punching/bending/cutting machine最先出现在Professional machinery supplier。

Specifications of Busbar punching machine

Busbar punching machine/Bending apparatus/Cutting device/Crimping instrument

Hydraulic Punching machines for Busbar最先出现在Professional machinery supplier。

Hydraulic pump for busbar bending machine

Manual hydraulic Busbar bending machine最先出现在Professional machinery supplier。

Mini dumper small construction machinery最先出现在Professional machinery supplier。

Automatic welding production line for IBC Frames最先出现在Professional machinery supplier。

The automatic welding production lines can be designed according to different type of workpieces, such as IBC frame, Cathode lines, SUS workpieces etc.

Specifications automatic welding production lines

Rated capacity	250*2 kVA +160*2 kVA
Rated power supply voltage	380VAC
Rated input current	400A
Rated load duration rate	20%
Insulation level	F
Secondary output maximum voltage	11 V
Rated air source pressure MPa	0.6
Cooling water flow rate L/min	48

Automatic welding production lines for workpiece最先出现在Professional machinery supplier。